|
The use of various types of tension maintenance
The use of various types of tension maintenance
Mechanical tensioner
Mechanical tension device in the installation of the rotation should not be too large, will affect the firmness of the mosaic.
To prevent falling, damage to the ceramic and shell.
When the tension rod is installed, the locking screw must be aligned with the axis.
When using the line and the model does not match the use of reluctance.
No oil is added to the damping wheel. Do not open the self regulation.
Frequently replace the wool ring, so as not to block the mouth.
When the line wheel is abnormal or not, please replace it in time.
If the damping wheel appears to slip, please use the cotton dipped in alcohol to remove the O ring in the damping wheel
In order to remove the wax residue inside the enameled wire.
To keep the production site clean, long time dust backlog easy to wear tension parts.
The bottom of the tension knob can only rotate around, can not pull down.
Magnetic tension device
The tension lever should not be higher than the red line position when working.
In the course of the work, only the tension is allowed to be small and not allowed in the major.
Zhang Lixu must be stopped in a major hour, so as not to cause a break.
For example, in the adjustment of tension pulsation phenomenon, the first to adjust the tension of the rotating disk to the maximum tension, and then slowly retreat
Go back to the required tension and readjust
Tension in the installation of the screw should not be too large, will affect the firmness of the mosaic.
To prevent falling, damage to the ceramic and shell. When the tension rod is installed, the locking screw must be aligned with the axis.
When using the line and the model does not match the use of reluctance.
No oil is added to the damping wheel.
Do not open the back cover to adjust.
Frequently replace the wool ring, so as not to block the mouth.
When the line wheel is abnormal or not, please replace it in time.
If the damping wheel rotation slip, please use the cotton dipped in alcohol to wipe the damping wheel in the O type ring, so that?
In order to remove the wax residue inside the enameled wire.
To keep the production site clean, long time dust backlog easy to wear tension parts.
Do not use for a long time or after a long period of use, such as tension instability, please stop, turn the small to big, from big to?
Repeated several times, you can restore the initial state.
If the use of the cylinder with the magnetic tension device, air pressure shall not be less than 5 kg.
Electronic tension device
To provide a stable DC24V power supply.
When used, it is best to have a horizontal position up to 15 degrees.
Connect the tension rod shaft should not be given additional pressure or impact, because the shaft is a high-precision sensor will affect its accuracy and normal use
3 adjustable resistors on the plate should not be adjusted.
Do not plug the power plug.
Do not have to put in a dry environment for a long time.
In the installation of the rotation should not be too large, will affect the firmness of the mosaic.
To prevent falling, damage to the ceramic and shell.
When the tension rod is installed, the locking screw must be aligned with the axis.
When using the line and the model does not match the use of reluctance.
No oil is added to the damping wheel.
Do not open the self regulation. Frequently replace the wool ring, so as not to block the mouth.
When the line wheel is abnormal or not, please replace it in time
If the damping wheel appears to slip, please use the cotton dipped in alcohol to remove the O ring in the damping wheel
In order to remove the wax residue inside the enameled wire. Keep production site clean, long time dust backlog
Easy to wear tension parts.
Such as in the production of tension pulsation (beating) phenomenon, first through the tension knob or control buttons to adjust to the maximum
The upper limit (i.e. the maximum tension), and then slowly callback, only 10% per time, and then turn a number of tension wheel,
By analogy, until the return to the lower limit of the tension can be eliminated by eliminating the magnetic pulse caused by the phenomenon
Servo tension device
To provide a stable DC24V power supply.
Connect the tension rod shaft should not be given additional pressure or impact, because the shaft is a high-precision sensor, will affect its accuracy and normal use.
Do not plug the power plug.
Do not have to put in a dry environment for a long time.
Mechanical tension device in the installation of the rotation should not be too large, will affect the firmness of the mosaic.
To prevent falling, damage to the ceramic and shell.
When the tension rod is installed, the locking screw must be aligned with the axis. When using the line and the model does not match the use of reluctance.
No oil is added to the damping wheel.
Do not open the self regulation.
Frequently replace the wool ring, so as not to block the mouth.
When the line wheel is abnormal or not, please replace it in time.
If the damping wheel appears to slip, please use the cotton dipped in alcohol to remove the O ring in the damping wheel
In order to remove the wax residue inside the enameled wire.
To keep the production site clean, long time dust backlog easy to wear tension parts.
Thread can only pull the line, can not be used to press the tension bar.
|
